Washing Machines – Essentials for Good Washing

1. Correct Water Temperature.

Hot water is essential for washing heavily soiled clothes. The water should be delivered to the washer at 140 to 160F. Hot water releases deeply embedded dirt quickly by opening up the fibers, dissolves detergents rapidly, and helps sanitize clothes. Warm water is for washing more delicate fabrics and lightly soiled articles and for rinsing clothes. Warm water softens synthetic fibers less, prevents setting excess wrinkles, preserves special finishes, and protects nonfast colors. Cold water is used for washing very delicate or lightly soiled items. Cold rinse water helps to prevent excess wrinkles in wash-and-wear garments.

2. Soft Water.

Hard water is the biggest reason for unsatisfactory washing results maytag washer repair los angeles, by any washing method. The minerals in the water combine with soap and soil to form soap curd. This soap curd turns clothes gray, makes fabrics harsh and stiff, and causes fabrics to wear out sooner. Ideally, soft water should be used for both washing and rinsing, for the curdlike substance may form during either process. Water may be softened with a mechanical water softener, by adding a packaged water conditioner, or with a combination of the two.

3. Right Amount of Detergent.

Since there is such a wide variety of soil within a load of clothes and between loads, it is difficult to stat an exact amount of detergent to use. As a general rule, in the top-loading machine follow the detergent manufacturer’s recommendations for the amount of detergent; then adjust the amount according to needs. Remember the following points.

a. As the hardness of the water increases, the amount of detergent needs to be increased.
b. As the amount of soil increases, the amount of detergent needs to be increased.
c. As the size of the load increases, the amount of detergent needs to be increased.
d. Be sure to measure the detergent.

Preparation of the Washer Loads

Here are several important factors to remind you about the preparation of loads for your automatic washer appliance.

1. Check labels on garments for special instructions.
2. Sort clothes carefully by degree of soil, type of fabric, colorfastness, and special handling.
3. Mend rips and tears before washing.
4. Remove spots and stains. A stain-removal chart is usually found in the care and use booklet.
5. Pretreat heavily soiled areas such as collars and cuffs by brushing a concentrated detergent solution into the fabric with a soft-bristled brush, sponge, or fingertips. To make solution, dissolve granular detergent in water. Use the same detergent for pretreating and washing.
6. Remove shoulder pads and nonwashable or delicate trim.
7. Place very delicate or linty articles in mesh laundry bags.
8. Clean out all pockets, brush dirt from cuffs, close zippers, fasten hooks, ties, belts and apron strings into bow knots.

Loading the Washer

For best results, no more than two double bed sheets or two equally large articles should be used in a large load. The rest of the load can be made up of smaller items. Mixed loads of large and small pieces give the best washing action. Large, bulky items such as chenille spreads and blankets are best washed alone.

Conditioning Clothes

Conditioning is recommended for clothes which have become harsh or grey from soap or detergent that has not been completely rinsed from them. This is one of the most frequent washability complaints. It may be necessary to condition clothes several times before the old soap or detergent is completely removed. The suds that may be noticed are formed by the old soap or detergent that is being pulled from the clothes. Conditioning should be continued until suds do not form in the washer water. Here are some conditioning tips you should be reminded of.

1. Prepare clothes and load into the washer.
2. Add 1 or 2 cups nonprecipitating water conditioner- in addition to amount normally used to soften the water. Do not add detergent.
3. Set washer for a hot water wash and warm water rinse. If necessary, because of color or fabric, use warm water in washer.
4. Set washing machine water saver at appropriate level for load being conditioned.
5. Set control dial for max washing time.
6. Start washer. About halfway through washer phase, stop machine and check the amount of suds. If suds do not break down, there is soap or detergent buildup in the clothes.
7. Restart washer and allow it to finish the cycle. Repeat process until suds no longer appear to wash water.

How to Properly Search for Dryer Parts

We will briefly explain the most common dryer failures and which dryer parts are more common. Don’t let searching for your parts be a pain!

As well all know money is tight these days and you can not afford a new dryer or let alone call a service man to fix it. So the most economical way is to fix it your self. Most repairs are common as in example, replacing the heating source or belt as broke or the machine is loud kenmore dryer repair los angeles.

Usually repairing the belts, heating element or igniter is fairly simple. The most common problems in Whirlpool brand dryers are the belts and element. General Electric dryers are usually an element or the glides supporting the drum.

Now until the rest of this article I will be giving you an example of Chris trying to repair his family’s dryer. First things first:

Find your dryer make and model
Locate the model number and write it down
Ask your self simply what is the problem ( if it is not obvious)
Search for appliance troubleshooting guides
Make appropriate testings/diagnostics
Search for discount dryer parts
Chris first found that his dryer was a Roper gas dryer. Model number 110.jur54d5 and his drum was not spinning. He then searched to find out how to fix the issue and started taking apart the dryer and found his belt was shredded to pieces. The belt was so bad he could not locate the original belt number. Putting in his model number into the dryer parts list found his belt.

Problematic Kitchen Appliances and How to Handle Them

Some unlucky people have returned home after a long hard day at work and nearly broke their neck as there’s water all over the kitchen floor. This is normally because somewhere in your kitchen one of the appliances has broken down or developed a fault and leaked everywhere. It could be a washing machine whose hose has come loose, or perhaps it’s the door seal of a dishwasher that has sprung a leak, the worst possible case has got to be your freezer stopping and now all your food is defrosted and likely fit for the bin rather than the dinner table.

Undoubtedly a frustrating affair maytag stove and oven repair pasadena, a broken appliance can cause not only financial strain because of the need to replace any broken appliances but also a decent amount of stress and anguish as you may need that particular appliance in a hurry such as having masses of laundry to do or a big meal to cook for. If you find yourself in this situation don’t panic, instead calmly call for an appliance repair team who could easily come to your home and fix the problem in record time.

Most kitchen appliances no matter what brand and model they are will be susceptible to the same kind of problems and so most engineers will have seen it all before, knowing exactly what jobs need doing and what parts need replacing. There are a lot people who have saved time, stress and money by calling a repairs engineer out and if you were in this situation then knowing that experienced engineers are on hand is a welcome thought.

A lot of people will have friends and family who may be handy with a spanner or wrench but without the proper training and experience you may cause more harm than good and could make the machine irreparable. Instead put your feet up and call on one of these companies to come out and repair your appliance, in your home, in a short space of time.

With most household and kitchen appliances covered and appointments that can be made at your convenience there are so many pluses to this service that you will be glad you called and didn’t have to go out and spend over the odds to get a quick replacement.

Issues Overlooked for Electrical Repairs

The need for electrical repairs can affect so many aspects of home living that it can make it downright uncomfortable to make it through morning preparations, daily tasks, and nighttime roaming. However, we aren’t talking about a neighborhood or city power outage. At least under those conditions you can remember that tens, hundreds or thousands of others are in it with you, struggling to make it without the comforts that electricity provides, and it can mean everything in some households. After all, this valuable utility is needed for lighting your home, keeping it warm, and heating your water or food on/in your stove. If you regularly have issues with it, you would probably try to go without it, but, as stated above, you need it in order to get ready for the day ahead or to make it through the day ahead. Therefore, several of the common causes of electrical repair will be explored here for new homeowners and renters. This is also for the consideration of those who have been without all or partial power and never really got down to the cause. In the past, you’ve just kind of waited it out or had the maintenance guy, or a family member fix it.

Electrical repairs can become necessary as the result of a tripped breaker lg stove and oven repair pasadena, outlets, or switches. Yes, there are several other issues that you can encounter in your home, but these are very common conundrums that can be simple or require professional assistance for correction. Regardless of how long you’ve been living in your home, you are likely to notice an issue by trying to flip a light switch when you first walk into the room. First, you may notice that the switch is warm. Or perhaps sometimes the light turns on and sometimes they don’t when you lift the switch, or you never really could figure out what that switch is supposed to do.

Second, outlets can be a little bit scary. If they are warm to the touch or sparking when you place a plug in or take it out, you will need to have a technician service it immediately to prevent damage or loss. They can also stop serving appliances, one works while the other does not, or entire walls of outlets do not work throughout your home. These are all frustrating conditions that you shouldn’t have to put up with.

Lastly, improper installation, actual community power outages and old blown fuses can be the cause of many professional electrical repair visits. Your wires may have deteriorated, been chewed, or are exposed somewhere along the way and need mending or replacement. It is important to remember that it is a source of heat that left unattended can cause a fire. So if you feel heat where there shouldn’t be any or see frequent sparking or are unable to use outlets, you are in need of an inspection and possible electrical repairs.

How to Replace your Broken Oven Element

The oven element in your electric range can burn out at any time. Unfortunately it always seems to happen at the most inopportune times, such as the week before Christmas or Thanksgiving.

Most elements do give warnings before burning out. They will often have a bright spot that will be noticed by the homeowner, just prior to burning out. If your element has a bright spot replace it as soon as possible. Waiting for the element to burn out is inadvisable because the oven thermostat or other electric components can be affected samsung stove and oven repair pasadena.

In all aspects of this job safety must come first. Use only the manufacturers original parts, not a cheaper substitute. Only attempt this repair when you have enough time, and patience, to do it properly. Remember, you will be dealing with 240 volts – that’s twice as much power as flows through your regular household circuits. Only attempt this repair with another adult present.

If you feel confident in your ability to safely replace an oven element then try the following method:

1… Disconnect range from electrical power, either by unplugging or turning off breakers. Pull range away from wall so all sides can be accessed.

2… Remove rear panel of range to expose the element wiring. Identify which element you suspect being burnt out.

3… Carefully remove the element wiring. They are usually screwed on connections. Avoid breaking the connections or stripping the screw head with your screwdriver.

4… Go to the front of the range. Locate the screws securing the element within the oven cavity. This may require a flashlight because they are usually covered in debris. Again use caution not to harm the screw heads. The screws may be very tight and will require patience to remove without harming. If the screws will not turn they will have to be drilled out using a high-speed drill. If this becomes necessary use caution not to chip the oven interior.

5… Remove the oven element. If it’s broken avoid touching the pieces with your bare hands. The pieces can be very sharp. Plus, the white powdered insulation contains harmful chemicals.

6… Proceed to a parts store to obtain a replacement. Make certain you have your make, model, and serial number. Manufacturers use a vast variety of elements. Each model, type, configuration, and wattage requirements will determine which element was installed in your range.

7… Install the new element and secure it with the screws. If the holes in the mounting plate don’t align you will have to drill holes in the cabinet interior. Carefully drill holes in the cabinet using a high-speed drill. Use caution not to let drill slip to avoid damaging or chipping the interior liner.

8… From the rear of the range reconnect the element wiring. Don’t bent the electrical connections or allow the screws to strip the threads. If the wiring is burnt the insulation must be cut back to expose undamaged wire. Cut the insulation back using a knife or wire-stripping tool.

9… With the new element installed plug the range back into the electricity. Start the oven and allow to run for five minutes. Disconnect the electricity and quickly feel the wiring insulation at the element connections. They should feel slightly warm, but not hot. A hot connection indicates a poor connection, or the possible failure of other components associated with the oven. If hot, it will be necessary to remove it and redo. Once satisfied with connections replace the rear panel and reinstall into counter.

10… Test the oven operation. All elements should go off and on as per normal.

11… Final step is to do a test run of the oven temperature. If you have an oven thermometer allow the oven to cycle off three or four times at a regular baking temperature. The thermometer should indicate same temperature at which the oven dial is set. As a confirmation bake something such as muffins or cookies as your test substance.

As the preceding has shown, replacing a burnt element is not a difficult repair. But, it is certainly one that should only be attempted by someone who is confident around electricity. If you are uncertain about your ability around high voltage, telephone an appliance repairperson for help.

An appliance repairperson can have your element replaced, tested, and operating in less than an hour. Less time than it will take you to find the part. Also, they will have all the tools and testers required to do the job quickly and safely.

Maintenance Tips for Pressure Washers

Gas-powered pressure washers are ideal for cleaning big outdoor projects such as houses, boats and cars. The pounds per square inch (PSI) of water supplied by gas-powered pressure washers make them better candidates for tackling heavy duty jobs than electric-powered pressure washers. However, as with any power tool, gas-powered pressure washers experience wear and tear over time and will most likely need some form of repair down the road. Below are some do-it-yourself tips for fixing common gas-powered pressure washer repair problems.

No Water Flow

• Remove the nozzle to check for blockage washer repair altadena. Proceed to clean the nozzle if any obstruction is found before putting it back in place. Check the hose for blockage as well.
• It’s possible the trigger gun might be defective. This problem can be resolved by purchasing a new one.

Low Pressure

• Check for blockages in the inlet and other parts. Clean the part to remove the obstruction before securing it back into its proper place.
• Other possible reasons for low pressure could be air leakage, a worn nozzle or water leakage in the discharge valve. For these problems, contact the manufacturer or a tool repair store for a replacement part.

Pump Making Loud Noise or Abnormal Vibrations

• Release the trigger gun to discharge any air in the pump. Proceed to look for water in the pump. If water is found, this might indicate the pump head seals are torn, which would then require purchasing a new pump.
• Look for bearings and connecting rods that are worn or broken. Talk to a professional at your local power tool repair shop about whether buying replacement parts will solve the problem, or if the situation requires a new pressure washer pump instead.

Other Problems

• Oil leakage due to a worn crankshaft seal or o-ring can be resolved by buying replacements. When adding oil, make sure to use the type recommended by the manufacturer.
• Water leaks are usually caused by hoses that are damaged or improperly attached. Buying a replacement hose will resolve this problem.

Proper care and routine check-ups of the operating system of your pressure washer should minimize any potential problems that might arise. Before trying to repair your gas-powered pressure washer, make sure to read the manufacturer guidelines in order to gain a better understanding of the problem. And don’t hesitate to call an authorized repair maintenance professional when uncertain of the problem or uneasy about performing the repair yourself.

Effective Solution for Reliable Household Appliances

Inoperative appliances can spell disaster for your home, but with professional appliance repair, you can get the dependable appliance performance you deserve. Providing cost-effective service and quality results, your appliance repairmen are here to serve you.

When your fridge breaks down or your washer starts leaking, it can create major problems in your home. But with today’s economy, it may not be in the budget to purchase a new refrigerator or washing machine. However, that doesn’t mean you just have to live with the mess, inconvenience, and other issues malfunctioning appliances make. Professional appliance repair is a cost-effective, relatively affordable solution for resolving problems with appliances large and small. Helping you get your appliances working reliably again in no time at all, skilled handymen can help you get the dependable appliances you need without having to break the bank appliance repair pasadena!

Expert repair services are available to troubleshoot, diagnose, and fix a full range of problems with appliances like dryers, stoves, washing machines, and more. They’ll be able to pinpoint the source of the issue–be it a loose bolt or a worn-out compressor–and perform the necessary service efficiently and effectively. Most even waive the service call fee with completed jobs, making your dishwasher or refrigerator repair even more affordable than you might think. Compare that with the high cost of going out and buying a new appliance: from the hassle of going to the store to the expense of a brand-new appliance to the cost of removing your old appliance and putting in the new one, the price can really get out of control fast. That’s why choosing repair instead of replacement just makes sense.

Some homeowners think that if they can save money by choosing appliance repair, they can save even more by fixing their appliances themselves. But in most cases, that simply isn’t true! Do-it-yourself appliance maintenance sounds great on paper, but almost always results in disaster. The simple truth is that your professional appliance handyman has experience and expertise far beyond what you can learn from a washer dryer repair manual in a few minutes. He or she can ensure that your appliances are disassembled, fixed, and put back together right the first time.

So instead of attempting a DIY dishwasher repair–and coming up with extra parts when the job is through or failing to resolve the initial problem at all–leave your appliances safely in the hands of the pros. Whether you need oven repair or washing machine repair, these guys can get the problem fixed efficiently, affordably, and effectively. So don’t pay more than you have to to get your household back up and running again, contact your area appliance services today!

 

Finding The Best Stand Mixer For Bread Dough

Nothing beats the fresh smell of home-made bread in the morning together with your favorite cheese and sausages. The trouble many faces is however the need for a proper way to prepare the bread. With the use of an automatic bread dough mixer this task becomes fairly easy. In this article we will discuss what to look for in a bread dough mixer when you want to make perfect morning-bread.

Capacity:

In-order to make enough bread-dough, the capacity of the stand mixer is important. We want a machine with enough capacity to mix everything together nicely without overspilling dough on the kitchen bench. A good capacity for your average household needs would be about 6 quarts. This is enough capacity to make four loafs of breads at a time. If your needs are higher than this, then you should perhaps take a look at a commercial mixer for bread dough as they have a higher capacity kitchenaid dishwasher repair los angeles .

Power:

To get the stand mixer to knead the dough efficiently. The electrical power of the engine on the machine must be enough. A good and powerful mixer should have over 500 watts of power to easily make bread dough.

Attachments:

For the mixer to do it’s job properly having the right kind of attachments to do it is a must. We want a mixer that have a metal flat beater and a spiral dough hook. This makes it knead the bread dough the right way and will lower the load of the machine while it is doing the mixing.

Ease of cleaning:

Try to get a machine with a design that makes it easy to clean. A seamless construction without any places for the dough to hide will make the cleaning of the mixer easier. Look for stand mixers that are made out of stainless steel. These machines have parts that can be put in the dishwasher and they are also easy to clean for hand.

Durability

A long-lasting quality mixer is made out of metal and not cheap plastic that will fail and break. Look for durable products that have steel gears. You also want other crucial pieces of the machine to be made out of stainless steel. This is a sign of quality and you will avoid the frustration of having to deal with a stand mixer that needs repairs.

Functions:

The basic functions of the mixer are important if you want to have enough control to make the perfect bread dough. We recommend that you get a bread dough mixer that have a variable speed setting and an automatic shut off and turn on feature. This will make your bread dough maker function automatically. Also look for a mixer that comes with overspilling protection. This will prevent any mess in the kitchen when you are making bread.

Our top mixer for making bread dough!

To get a mixer that have proven itself over and over again, and have all the properties that is required in a good stand mixer. I recommend you check out our review of the KitchenAid Professional 600. It is a consumer favorite for many years and many enjoy making perfect bread dough with it each day. You can find a link to the review below.

Washing Machine Repair

Is your washing machine giving you trouble? A broken washing machine can be quite the headache, forcing you to lug loads of laundry to the nearest laundromat or spend valuable time hand washing items in the sink.

If your machine is on the fritz, you may be inclined to rush out and buy a new washer. Washing machine replacement can be very expensive, though, and when you factor in time for researching features and scheduling delivery and hookup, much of the convenience associated with a new unit is lost. If you’re looking to save money and time, washing machine repair is your best bet whirlpool washer repair los angeles.

Some washing machine repairs are simple enough for you to handle yourself, while others require the expertise of a professional appliance repair technician. How can you tell which repair issues are suitable for a DIY job, and which to leave to the pros? Let’s break it down by looking at some of the most common washer issues:

Leaks
A leaking washing machine often evokes feelings of panic, and with good reason. The combination of soap, water, and intricate electrical wiring and digital panels is a volatile one. Add in the potential for water damage to floors and the surrounding surfaces, and you’ve got a recipe for disaster. Fortunately, most washer leaks are easy and inexpensive to resolve.

The first thing you’ll want to do is unplug your washing machine to ensure your safety. Check the door seals and gaskets for any wear and tear, especially in front-loading machines. If you see water leaking from the front of the machine, it’s a clear sign that the door gasket needs to be replaced. Most gaskets can easily be swapped out by the average homeowner; just check your washing machine repair manual for the correct part number.

If your door seal is in good condition, or you notice water leaking from the back or underneath the machine, there’s a good chance the leak is originating from the water inlet hoses on the back of the washer. Simply tighten the connections between the machine and the hot and cold hookups, and you should be good to go. If neither of these fixes solves the problem, your machine may be overfilling due to a malfunctioning water level sensor. Due to the complex electronic components involved, this is a washing machine repair best left to the professionals.

Excessive Noise
Does your washing machine rattle or thump? Does it shimmy across your laundry room during each cycle? The most likely culprit is an unbalanced drum. Make sure that you’re distributing the weight of your laundry evenly throughout the tub. It’s also important to make certain your machine is level with the floor. You can level the washer yourself by simply adjusting the legs on the bottom of the machine. You want your washer to be as close to the floor as possible. Placing the machine on a rubber-backed carpet can also help to keep it in place and minimize noise.

A loose drum or motor mount can also cause loud banging sounds when your washer is running. While it is fairly simple to tighten the bolts for the drum and motor mount, it can be quite difficult to access those parts of the washer. The motor mount is usually located under the tub, and you may have to lean the machine to one side while simultaneously supporting the mount in order to access it. If you’re having a hard time getting to this part of the washer, it may be time to call in your local washer/dryer repair specialist for help. If these minor adjustments don’t resolve the issue, you may be in need of a motor replacement. Contact your local appliance repair company for more information.

Failure to Spin
If your washing machine doesn’t spin, and is leaving your clothes sopping wet, there could be a number of issues to blame. As with all washing machine repairs, it is important to unplug your washer before you begin working on it. The easiest solution is to check the belts at the back of the machine. If the belts are getting stuck on another component, it could prevent your machine from spinning properly. Over time, the belts may become worn, necessitating replacement: a simple washing machine repair that you can do on your own. If the belts are intact and moving freely, the lid switch may be at fault. The lid switch is typically located near the door hinge at the front or top of the machine. To determine whether the lid switch is functioning properly, hold the door open, and depress the switch using a pen or similar object. If the machine begins to spin normally, the lid switch and plunger aren’t making good contact, and probably need to be replaced. This should be an easy fix as long as you consult your appliance repair manual for the appropriate part numbers and installation instructions. Some other issues that can result in failure to spin include a motor mounting plate that needs to be adjusted or replaced, a worn motor coupling, and a bad clutch. Addressing these issues requires a lot of work, and an in-depth knowledge of the inner workings of your washing machine. In other words, these are repairs best left to professionals experienced in home appliance repair.

Do-it-yourself washing machine repairs can save you time and money, particularly over replacing your machine. There are some circumstances, however, under which you should always contact an appliance repair professional. For example, if you’re in doubt as to what is causing the problem, it’s best to call in the experts. Your washing machine is made of a number of intricate parts, and if you’re not sure what you’re doing, you run the risk of making the problem worse, or creating new issues. Any washing machine repair that requires wiring or electrical work is also typically best left to the pros.

 

Electric Pressure Washer A Perfect Machine for Auto Detailing

Auto detailing is a lucrative venture that many people all over the world are turning to on a regular basis. However, it is not easy to survive the competition and emerge successful. To do so, your car wash professionals must be equipped with high-grade machines capable of cleaning vehicle exteriors and making them sparkling and as good-as-new. The vehicle detailing systems must also be technologically advanced to manage the cleaning jobs of fleets, boats and airplanes. Most importantly, using top-grade electric pressure washer machines to clean vehicles will keep customers happy and ensure that they keep coming back samsung washer repair pasadena.

Designed for Car Washing Applications
Quality car cleaning systems available from leading distributors offer lots of benefits for users. These electric pressure washer units have been designed exclusively for auto detailing jobs and thus feature the technologies required to clean and maintain vehicles with minimum time and effort. Some of the notable features in these power cleaners include:
Excellent construction: The best electric pressure washer machines feature solid construction of powder coated stainless steel. The steel housing is also chemical resistant and chip resistant making it durable and perfect for demanding cleaning tasks.
High grade components: The best selling versions of car wash systems feature top quality components such as stainless steel housing, self-cleaning boilers and replaceable heating components. Quality components guarantee reliable performance, user safety and minimum maintenance issues.
Cleaning technologies: Thanks to the perfect combination of average pressure levels, high steam temperatures and low flow rates, these electric pressure washer machines offer the most efficient auto detailing results.
By neatly combining steam cleaners and pressure cleaners, a car wash system features the benefits of both these classes of machines. It eliminates the low pressure levels of steam cleaners while retaining the high steam temperatures. It does not have the extremely high pressure levels of traditional gas pressure washers and maintains average pressure levels to make it great for washing vehicles without causing scratches or damage to vehicle exteriors.

Always choose a hot water pressure washer that has been specifically designed for auto detailing operations. Such pressure washing equipment comes with low flow rates as low as 0.5 GPM. As a result, it does not pose any risk to delicate components such as engine compartments. Low flow rates also imply lower water consumption and thus a positive step towards water conservation. These high pressure washers feature pressure levels of 1000 psi to help efficiently eliminate caked mud, dirt and grease deposits from vehicle exteriors.

These pressure washers also generate steam temperatures of up to 250ºF. This steam ejected by the hot water pressure washer thus dissolves and cleans off tough dirt deposits such as bird discharge, squashed bugs and tree sap from vehicle exteriors. This steam pressure washing equipment is great for melting away the snow that blankets vehicles in winter.